Relationship between internal stress distribution and microstructure in a suspension-sprayed thermal barrier coating with a columnar structure

Yamazaki, Yasuhiro*; Shinomiya, Keisuke*; Okumura, Tadaharu*; Suzuki, Kenji*; Shobu, Takahisa; Nakamura, Yuiga*

Quantum Beam Science (Internet), 7(2), p.14_1 - 14_12, 2023/05

https://doi.org/10.3390/qubs7020014

Experimental and analytical investigations on aerosol washout in a large vessel with high spray coverage ratio simulating PWR containment spray

Sun, Haomin; Leblois, Y.*; Gelain, T.*; Porcheron, E.*

Journal of Nuclear Science and Technology, 59(11), p.1356 - 1369, 2022/11

https://doi.org/10.1080/00223131.2022.2055673

In severe accident scenarios of PWR, containment spray can be employed to washout the aerosol of radioactive materials, retaining them in the containment. Therefore, it is crucial to correctly predict the washout efficiency for safety assessment. For a PWR, a high spray coverage ratio ( 84%-95%) is required. However, experimental studies on the washout with such a high coverage ratio in a large vessel are quite limited. To understand such a washout phenomenon for model development, aerosol washout experiments are performed in a large vessel with not only aerosol measurements but also spray droplet characterizations. The spray coverage ratios are experimentally confirmed to be compatible with a real PWR. The washout features are investigated in detail. The model in MELCOR is examined using the measured aerosol removal rate, showing the removal rate tendency against particle diameters being reproduced. Although a significant underestimation occurs for large particles, a satisfactory agreement is obtained for smaller ones (0.52 m in diameter) corresponding to the minimum removal rate and around.

Development of the technology for preventing radioactive particles' dispersion during the fuel debris retrieval (Contract research); FY2019 Nuclear Energy Science & Technology and Human Resource Development Project

Collaborative Laboratories for Advanced Decommissioning Science; The University of Tokyo*

JAEA-Review 2020-043, 116 Pages, 2021/01

JAEA-Review-2020-043.pdf:7.74MB

The Collaborative Laboratories for Advanced Decommissioning Science (CLADS), Japan Atomic Energy Agency (JAEA), had been conducting the Nuclear Energy Science & Technology and Human Resource Development Project (hereafter referred to "the Project") in FY2019. The Project aims to contribute to solving problems in the nuclear energy field represented by the decommissioning of the Fukushima Daiichi Nuclear Power Station, Tokyo Electric Power Company Holdings, Inc. (TEPCO). For this purpose, intelligence was collected from all over the world, and basic research and human resource development were promoted by closely integrating/collaborating knowledge and experiences in various fields beyond the barrier of conventional organizations and research fields. The sponsor of the Project was moved from the Ministry of Education, Culture, Sports, Science and Technology to JAEA since the newly adopted proposals in FY2018. On this occasion, JAEA constructed a new research system where JAEA-academia collaboration is reinforced and medium-to-long term research/development and human resource development contributing to the decommissioning are stably and consecutively implemented. Among the adopted proposals in FY2018, this report summarizes the research results of the "Development of the technology for preventing radioactive particles' dispersion during the fuel debris retrieval" conducted in FY2019. In this study, a technique to effectively suppress the scattering of fine particles has been developed, and as a result of experiments, a method of spraying with water mist was found to be an effective and applicable method for improving aerosol removal efficiency and removal rate. As a method of solidifying fuel debris to suppress fine particle scattering during cutting, geopolymer was evaluated for its strength, thermal conductivity and cutting powder. In addition, flow status of geopolymer and the temperature distribution inside RPV covered by geopolymer were simulated.

Development of technology to prevent scattering of radioactive materials in fuel debris retrieval (Contract research); FY2018 Center of World Intelligence Project for Nuclear Science/Technology and Human Resource Development

Collaborative Laboratories for Advanced Decommissioning Science; The University of Tokyo*

JAEA-Review 2019-037, 90 Pages, 2020/03

JAEA-Review-2019-037.pdf:7.0MB

JAEA/CLADS, had been conducting the Center of World Intelligence Project for Nuclear Science/Technology and Human Resource Development (hereafter referred to "the Project") in FY2018. The Project aims to contribute to solving problems in nuclear energy field represented by the decommissioning of the Fukushima Daiichi Nuclear Power Station, Tokyo Electric Power Company Holdings, Inc. For this purpose, intelligence was collected from all over the world, and basic research and human resource development were promoted by closely integrating/collaborating knowledge and experiences in various fields beyond the barrier of conventional organizations and research fields. The sponsor of the Project was moved from the Ministry of Education, Culture, Sports, Science and Technology to JAEA since the newly adopted proposals in FY2018. On this occasion, JAEA constructed a new research system where JAEA-academia collaboration is reinforced and medium-to-long term research/development and human resource development contributing to the decommissioning are stably and consecutively implemented. Among the adopted proposals in FY2018, this report summarizes the research results of the "Development of Technology to Prevent Scattering of Radioactive Materials in Fuel Debris Retrieval". The objective of the present study is to clarify the behavior of microparticles in gas and liquid phases in order to steadily confine radioactive microparticles at the time of debris retrieval in Fukushima Daiichi Nuclear Power Station. In addition, as measures to prevent scattering, we will evaluate and develop methods by experiments and simulation as to; (1) a method to suppress the scattering with minimum amount of water utilizing water spray etc., and (2) a method to suppress the scattering by solidifying fuel debris.

Epistemic Uncertainty Quantification of Floor Responses for a Nuclear Reactor Building

Choi, B.; Nishida, Akemi; Li, Y.; Muramatsu, Ken*; Takada, Tsuyoshi*

Proceedings of 26th International Conference on Nuclear Engineering (ICONE-26) (Internet), 9 Pages, 2018/07

After the 2011 Fukushima accident, nuclear power plants are required to take countermeasures against accidents beyond design basis conditions. In seismic probabilistic risk assessment (SPRA), uncertainty can be classified as either aleatory uncertainty, which cannot be reduced, or epistemic uncertainty, which can be reduced with additional knowledge and/or information. To improve the reliability of SPRA, efforts should be made to identify and reduce the epistemic uncertainty caused by the lack of knowledge. In this study, we focused on the difference in seismic response by modeling methods, which is related epistemic uncertainty. We conducted a seismic response analysis with two kinds of modeling methods; a three-dimensional finite-element model and a conventional sway-rocking stick model, by using simulated various input ground motions, which is related to aleatory uncertainty. And then we quantified the seismic floor response results of the various input ground motions of each modeling methods. For the uncertainty quantification related to different modeling methods, we further perform a statistical analysis of the floor response results of the nuclear reactor building. Finally, we discussed how to utilize the results from these calculations for the quantification of uncertainty in fragility analysis for SPRA.

Impacts of friction stir processing on irradiation effects in vacuum-plasma-spray coated tungsten

Ozawa, Kazumi; Tanigawa, Hiroyasu; Morisada, Yoshiaki*; Fujii, Hidetoshi*

Fusion Engineering and Design, 98-99, p.2054 - 2057, 2015/10

https://doi.org/10.1016/j.fusengdes.2015.06.104

Reduced activation ferritic/martensitic steel, as typified by F82H, is a promising candidate for structural material of DEMO fusion reactors. To prevent plasma sputtering, tungsten (W) coating was essentially required. This study aims to examine the irradiation effects on hardness and microstructure of vacuum-plasma-spray coated W-F82H steel, with a special emphasis on the impacts of grain-refining induced by frictional stir processing (FSP). It was revealed that the hardness of the VPS-FSP W after ion-irradiation to 5.4 dpa at 800C were not remarkably changed, where bulk W usually exhibited significant irradiation hardening.

Sodium combustion computer code ASSCOPS Version 2.1; User's manual

Ohno, Shuji; Matsuki, Takuo*; ; Miyake, Osamu

JNC TN9520 2000-001, 196 Pages, 2000/01

JNC-TN9520-2000-001.pdf:5.13MB

ASSCOPS (Analysis of Simultaneous Sodium Combustion in Pool and Spray) has been developed for analyses of thermal consequences of sodium leak and fire accidents in LMFBRs. This report presents a description of the computational models, input and output data as the user's manual of ASSCOPS version 2.1. ASSCOPS is an integrated computational code based on the sodium pool fire code SOFIRE II developed by the Atomics International Division of Rockwell International, and on the sodium spray fire code SPRAY developed by the Hanford Engineering Development Laboratory in the U.S. The users of ASSCOPS need to specify the sodium leak conditions (leak flow rate and temperature, etc.), the cell geometries (cell volume, surface area and thickness of structures, etc.), and the atmospheric initial conditions such as gas temperature, pressure, and composition. ASSCOPS calculates the time histories of atmospheric temperature, pressure and of structural temperature.

Development and validation of sodium fire analysis code, ASSCOPS

; ; Tanabe, Hiromi; Ohno, Shuji; Miyake, Osamu;

PNC TN9410 97-030, 93 Pages, 1997/04

PNC-TN9410-97-030.pdf:2.2MB

A sodium fire analysis code, ASSCOPS(Analysis of Simultaneous Sodium Combustions in Pool and Spray) was developed coupling the computer codes of SPRAY-IIIM and SOFIRE-MIl to assess temperature-pressure transients resulting from sodium spray and pool combustions, simultaneously. The validation of ASSCOPS was conducted using the experimental results obtained from sodium spray fire experiments using 21 m vessel and the accuracy of calculated results was discussed. The following results were obtained: (1)Study under inert gas atmosphere. The comparison between analysis and experiment with regard to the pressure and the temperature showed a good agreement. (2)Study under air atmosphere. The comparison between analysis and experiment with regard to the pressure and the temperature also showed a good agreement. (3)Effects of parameter used in evaluating the design of Monju. The peak pressure and temperature obtained by the analysis overestimates the experimental results. From these results, it was concluded that the development and validation of ASSCOPS indicate a improvement on the burning and the heat transfer models in SPRAY-IIIM.

Electrical insulation and conduction coating for fusion experimental devices

Onozuka, Masanori*; Tsujimura, Seiji*; Toyoda, Masahiko*; Inoue, Masahiko*; Abe, Tetsuya; Murakami, Yoshio

Fusion Technology, 29(1), p.73 - 82, 1996/01

https://doi.org/10.13182/FST96-A30657

no abstracts in English

Experimental and analytical study on the behavior of cesium iodide aerosol/vapor deposition onto inner surface of pipe wall under severe accident conditions

Hidaka, Akihide; Igarashi, Minoru*; Hashimoto, Kazuichiro; ; *; Sugimoto, Jun

Journal of Nuclear Science and Technology, 32(10), p.1047 - 1053, 1995/10

https://doi.org/10.3327/jnst.32.1047

no abstracts in English